FK ATC COM Trainer is an interactive aviation communication training tool designed to help student pilots and private pilots practice the sequence, structure, and readback of common ATC radio calls. The trainer guides the pilot through a complete VFR communication flow, including departure ATIS, clearance delivery, ground, tower, departure, approach, arrival ATIS, destination tower, and destination ground.
Pilots use the FK COM 1 panel to tune the required frequency. When the correct frequency is selected, the radio displays READY, and the pilot can use Tap to Talk to transmit or enter the call text via the text box. The trainer responds with simulated ATC instructions and evaluates important elements such as callsign, destination, runway, taxiway, altitude, ATIS code, squawk code, frequency readback, and other required information. The trainer also provides stage-by-stage feedback, identifies missing items, introduces scenario variation, and provides an end-of-flight report with scores, retries, tuning errors, and recommended areas for additional practice.
The goal is to improve confidence, radio discipline, situational awareness, frequency management, readback accuracy, and familiarity with the normal rhythm of pilot–ATC communication.
FK ATC COM Trainer is a training aid only. It is not a substitute for current FAA publications, official airport information, actual ATC instructions, or flight training with a qualified instructor.
Set Up Your Flight
Flight Setup section → Click on "Tap to Expand"
Select the departure airport, destination airport, aircraft, runway, altitude, and training level. Tap Apply Setup.
Click on "Tap to Collapse" at the bottom of the Flight Setup section
Tune FK COM 1
Use the + and − controls to tune the radio to the Target Frequency. The panel will show READY when the correct frequency (118 - 137 MHz) is selected.
Listen to ATIS or ATC
Follow the instructions for the current stage. For ATIS stages, monitor the broadcast and note the important information.
Make Your Radio Call
When the radio shows READY, tap Tap to Talk, speak your transmission, then tap again to end and send. You may also type the transmission in the text box.
Review the Feedback
The trainer checks your call for required items such as callsign, runway, destination, ATIS code, altitude, squawk, and readback information.
Continue the Flight
Complete each stage, then select Next → and tune the new frequency. The trainer progresses through Clearance, Ground, Tower, Departure, Approach, Arrival ATIS, Destination Tower, and Destination Ground.
Review Your Results
At the end of the session, review your score, retries, missed items, tuning errors, and recommended areas for additional practice.
A Alfa
B Bravo
C Charlie
D Delta
E Echo
F Foxtrot
G Golf
H Hotel
I India
J Juliett
K Kilo
L Lima
M Mike
N November
O Oscar
P Papa
Q Quebec
R Romeo
S Sierra
T Tango
U Uniform
V Victor
W Whiskey
X X-ray
Y Yankee
Z Zulu
This example covers all nine VFR stages in FK ATC COM Trainer, from departure ATIS to arrival parking.
Flight Setup — Select Fullerton (KFUL) → Brackett (KPOC), Cessna 172, N123FK, Main Ramp, Runway 24 for takeoff, Runway 26R for landing, Northeast departure, 3,000 requested altitude, and General Aviation (GA) Parking for arrival. Select Apply Setup.
The ATIS codes, squawk, and pattern entry below are examples. Use the values and instructions you receive in your session. Say N123FK as November One Two Three Foxtrot Kilo. If ATC shortens it to Cessna 3FK, you can use that abbreviation with that controller.
Tune 125.050 and select Monitor ATIS. Note the information code and runway in use. This example uses Uniform and Runway 24.
Select Next and tune Fullerton Clearance on 121.800.
Note: KFUL uses 121.8 for Ground and Clearance. Call Ground to obtain clearance.
Pilot — “Fullerton Ground, N123FK is a Cessna 172, at the GA parking, with information _____, request VFR flight following to Brackett, 3,000.”
ATC — “Cessna 3FK, Fullerton Ground, on departure turn left heading 120, departure frequency 125.35, squawk 3670.”
Pilot readback — “left heading 120, departure frequency 125.350, squawk 5132. Cessna 3FK”
ATC — "Cessna 3FK, readback correct. Remain on this frequency and call when ready to taxi."
Select Next for Fullerton Ground. The trainer uses 121.800 for both stages, so leave the radio tuned there.
Pilot — “Fullerton Ground, Cessna 123FK, at GA parking, with India, request taxi to the run-up area, Runway 24.”
ATC — “Cessna 3FK, Fullerton Ground, runway 24, taxi via Alpha. Run-up approved. ”
Pilot readback — “Runway 24, taxi via Alpha, run-up approved, Cessna 3FK.”
Select Next and tune Fullerton Tower on 119.100. Make the Tower call after completing the run-up and reaching the hold-short line.
Pilot — “Fullerton Tower, Cessna 123FK, holding short Runway 24, ready for VFR departure.”
ATC — “Cessna 3FK, Runway 24, cleared for takeoff.”
Pilot readback — “Runway 24, cleared for takeoff, Cessna 3FK.”
ATC — "Cessna 3FK, Fullerton Tower, on departure, turn left heading 120, contact SoCal Departure."
Pilot — "Left 120, contact SoCal Departure, Cessna 3FK"
When the trainer advances to the departure check-in, select Next and tune SoCal Departure on 125.350.
Pilot — “SoCal Departure, Cessna 123FK, passing 1,500, climbing to 2,500.”
ATC — “Cessna 123FK, radar contact. Climb and maintain 3,000.”
Pilot readback — “Climb and maintain 3,000, Cessna 123FK.”
Select Next and tune Brackett ATIS on 124.400.
Tune 124.400 and select Monitor ATIS. Note the information code and landing runway. This example uses Alpha and Runway 26R.
Select Next and tune SoCal Approach on 125.500.
Pilot — “SoCal Approach, Cessna 123FK, level at 3,000, ten miles southwest, with information Alpha, inbound for a full-stop landing.”
ATC — “Cessna 123FK, proceed direct Brackett Field. Expect visual approach.”
Pilot readback — “Proceed direct Brackett, expect visual, Cessna 123FK.”
Select Next and tune Brackett Tower on 118.200.
Pilot — “Brackett Tower, Cessna 123FK, five miles southwest, with information Alpha, inbound for a full-stop landing, Runway 26L.”
ATC — “Cessna 3FK, enter left downwind Runway 26L, extend downwind, I will call your base ”
Pilot readback — “Left downwind, 26L, extend downwind, you will call base, Cessna 123FK”
Unexpected go-around. Read back the go-around instruction.
ATC — “Cessna 3FK, go around. Fly runway heading, remain in the pattern."
Pilot readback — “Going around. Runway heading, remain in the pattern, Cessna 123FK."
ATC — “Cessna 3FK, roger. Make left traffic Runway 26L."
Pilot readback — “26L, cleared to land, Cessna 123FK.”
After landing and clearing the runway, select Next and tune Brackett Ground on 125.000.
Pilot — “Brackett Ground, Cessna 123FK, clear of Runway 26L, request taxi to general aviation parking.”
ATC — “Cessna 123FK, taxi to general aviation parking via Alpha.”
Pilot readback — “Taxi to general aviation parking via Alpha, Cessna 123FK.”
When the final stage is complete, select Next to open the End-of-Flight Report.
Here’s an interactive demo video showcasing a flight from Long Beach (KLGB) to McClellan-Palomar (KCRQ).
An interactive demo flight from Long Beach (KLGB) to McClellan-Palomar (KCRQ)! Follow the complete ATC communication experience, from clearance delivery and taxi instructions to takeoff, flight following, approach, and landing.